Do You like your car?

Dodane: 02-09-2016 12:05
Do You like your car? best oil for Audi

4-stroke engines

4-stroke engines
Main article: 4-stroke engine
Diagram showing the operation of a 4-stroke SI engine. Labels:
1 ? Induction
2 ? Compression
3 ? Power
4 ? Exhaust

The top dead center (TDC) of a piston is the position where it is nearest to the valves; bottom dead center (BDC) is the opposite position where it is furthest from them. A stroke is the movement of a piston from TDC to BDC or vice versa together with the associated process. While an engine is in operation the crankshaft rotates continuously at a nearly constant speed. In a 4-stroke ICE each piston experiences 2 strokes per crankshaft revolution in the following order. Starting the description at TDC, these are:78

Źródło: https://en.wikipedia.org/wiki/Internal_combustion_engine


The cylinder head

The cylinder head is attached to the engine block by numerous bolts or studs. It has several functions. The cylinder head seals the cylinders on the side opposite to the pistons; it contains short ducts (the ports) for intake and exhaust and the associated intake valves that open to let the cylinder be filled with fresh air and exhaust valves that open to allow the combustion gases to escape. However, 2-stroke crankcase scavenged engines connect the gas ports directly to the cylinder wall without poppet valves; the piston controls their opening and occlusion instead. The cylinder head also holds the spark plug in the case of spark ignition engines and the injector for engines that use direct injection. All CI engines use fuel injection, usually direct injection but some engines instead use indirect injection. SI engines can use a carburetor or fuel injection as port injection or direct injection. Most SI engines have a single spark plug per cylinder but some have 2. A head gasket prevents the gas from leaking between the cylinder head and the engine block. The opening and closing of the valves is controlled by one or several camshafts and springs?or in some engines?a desmodromic mechanism that uses no springs. The camshaft may press directly the stem of the valve or may act upon a rocker arm, again, either directly or through a pushrod.
Engine block seen from below. The cylinders, oil spray nozzle and half of the main bearings are clearly visible.

The crankcase is sealed at the bottom with a sump that collects the falling oil during normal operation to be cycled again. The cavity created between the cylinder block and the sump houses a crankshaft that converts the reciprocating motion of the pistons to rotational motion. The crankshaft is held in place relative to the engine block by main bearings, which allow it to rotate. Bulkheads in the crankcase form a half of every main bearing; the other half is a detachable cap. In some cases a single main bearing deck is used rather than several smaller caps. A connecting rod is connected to offset sections of the crankshaft (the crankpins) in one end and to the piston in the other end through the gudgeon pin and thus transfers the force and translates the reciprocating motion of the pistons to the circular motion of the crankshaft. The end of the connecting rod attached to the gudgeon pin is called its small end, and the other end, where it is connected to the crankshaft, the big end. The big end has a detachable half to allow assembly around the crankshaft. It is kept together to the connecting rod by removable bolts.

The cylinder head has an intake manifold and an exhaust manifold attached to the corresponding ports. The intake manifold connects to the air filter directly, or to a carburetor when one is present, which is then connected to the air filter. It distributes the air incoming from these devices to the individual cylinders. The exhaust manifold is the first component in the exhaust system. It collects the exhaust gases from the cylinders and drives it to the following component in the path. The exhaust system of an ICE may also include a catalytic converter and muffler. The final section in the path of the exhaust gases is the tailpipe.

Źródło: https://en.wikipedia.org/wiki/Internal_combustion_engine


The importance of transport

Public transport is of utmost importance. You can quickly reach the first place, above all those who do not own a car. On the other hand, using the bus or smaller buses can get rid of the problem of parking the, which is often quite confusing for drivers. The bus ride makes it not need to be focused on driving. It is not surprising that this mode of transport is still often used on Polish roads. True, much of the buses is a machine that would give longer to the museum associated with the automotive industry, but there is also a really modern, rich in many of the features of vehicles on the road. The use of the exclusive bus is a feature of organized tours and I must admit that this is undoubtedly advantage of long journeys.



© 2019 http://ac-net.com.pl/